Photo Gallery

Rough install of the new model 480. Can be mounted up or down.

Rough install of the new model 480. This unit can be mounted up or down.

Model 480 Dryerbox showing upward airflow and aluminum semi-rigid flex

Model 480 Dryerbox shown trimmed out with door casing as an option

Nice install photo of a model 480 mounted up a bit for a dryer on a pedestal

Rough install of a 480 unit mid-wall for a stacked dryer, note the two Dryer-Ell 45's

Nice install image of a model 480 Dryerbox

Nice install image of a model 480 Dryerbox

Nice install image of a model 480 Dryerbox with dryer connected (DryerFlex)

Nice use of two 45 degree Dryer-Ells

This is a long turn Dryer-Ell. Amazingly efficient and saves 5 feet of duct run.

The use of the long turn Dryer-Ells likely saved this builder from a red-tag

Model 425 venting sideways

Initial CAD rendering from 1999 showing preferred port penetration distance

Model 350 and 425 for upward ventilation

Model 425 Dryerbox is bulk packed 5 per carton

Model 425 Dryrebox properly installed in rough framing stage

Exhaust pipe penetrating is excessive - only needs to be 1.6 through

Exhaust pipe penetrating is excessive - only needs to be 1.6 through

Dryerbox 425 installed in 2x6 framed wall

Dryerbox 425 installed in 2x6 framed wall with fire-caulking

Dryerbox 350 mid-wall installation for stacked washerdryer

Correct Termination Assembly for Gas Line to Dryerbox - CSST Fitting

Correct Termination Assembly for Gas Line to Dryerbox - CSST Fitting

Image demonstrates how to prep support tab to hold exhaust conduit

Dryerbox support tab temporarily supporting the rigid pipe

Proper rough install of Dryerbox model 425

This awkward install does not provide the full benefits to the owner. Model 4D would be the preferred.

Model 425 Dryrebox properly installed in rough framing stage

Good example of why it is best to have Dryerbox installed prior to plumber rough

Exhaust pipe penetrating is excessive - only needs to be 1.6 through

Nice picture sent in, properly installed, showing a to-the-side exhaust direction

This mid-wall install of a Dryerbox 425 is proper for a dryer on a typical pedestal

Interesting image showing rough and final install of a Model 425 Dryerbox

Drywall is zip cut around Dryerbox receptacle, excessive pipe penetration

Close-up of post Zip-Cut drywall to be caulked by painter

Caulk joint between Dryerbox and drywall

Close-up of recommended baseboard termination

Nicely caulked Dryerbox model 425

Model 425 Dryerbox with foil flex to dryer

Consequence of not having a Dryerbox receptacle

Consequence of not having a Dryerbox receptacle

Severely crushed exhaust hose. Badly need a Dryerbox here.

Two views of a 425 Dryerbox install (foil flex and aluminum flex)

Model 425 Dryerbox ready for dryer appliance.

Model 425 shown painted with same paint as baseboard

Model 425 shown painted with same paint as baseboard

Flex stretched out to make the connection, ready to move dryer back

Model 425 shown painted with same paint as baseboard

In the process of moving the dryer all the way back, no way to crush hose

Dryer pulled away a little to take the photo. Super efficient and very safe.

Dryer pulled away a little to take the photo. Super efficient and very safe.

The red label is the Dryer Placard that is a code required item

Nice looking install sent in from a customer

Install sent in from customer. Used door casing to trim the receptacle out.

Close-up of a stacked dryer connection and using the DryerFlex product

Demonstration summary of going up and going down with vent direction

4D Dryerbox rendering showing how the flex loops back around to the dryer

Rough install of a 4D Dryerbox for going down with the ventilation

Rough install of a 4D Dryerbox

Rough install of a 4D Dryerbox

Retro-install of a 3D Dryerbox, but rigid pipe is longer than recommended

Proper flex connection on a down box 4D Dryerbox

Customer sent in photo of a 4D with gas connection

Customer sent in photo of a 3D with gas run outside the wall

Customer photo where they took a unit with no hole and cut their own in

Nice looking install sent in from a customer of a 3D Dryerbox

Glamour shot of a RetroFit model 500 Dryerbox, note the flange location

Install image of a Retrofit model 500 with aluminum semi-rigid flex hose

Close-up of a Retro-fit 400 Dryerbox with dryer moved all the way back

Customer image of a Model 400 Retro-Fit unit mounted mid-wall for stacked setup

Customer image of a Model 400 Retro-Fit unit